Peopoly Phenom XXL Resin Settings for 3DRS Resins
On the Peopoly Phenom XXL, start 3DRS HERO HD Medium Grey at 10.6 s per layer at 50 microns, RPG at 13.9 s and Standard HD Dark Cool Grey at 20.0 s. Use 6 burn in layers at 62.3 s. Every resin colour has its own card below with 30, 50 and 100 micron values.
- Release: Single stage lift
- Screen: 3840 x 2160
- XY pixel: 137.2 µm
- Build volume: 527 x 296.5 x 550 mm
- File format: ctb, cbddlp
HERO HD RPG Standard HD Platinum Cure Cast Lift and retract FAQ All printers
HERO HD settings on the Peopoly Phenom XXL
HERO HD Medium Grey
HERO HD Medium Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer10.4 sRange 10.3 to 10.5 s
- 50 µm layer10.6 sRange 10.5 to 10.7 s
- 100 µm layer11.6 sRange 11.5 to 11.7 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
HERO HD Light Grey
HERO HD Light Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer11.1 sRange 11.0 to 11.2 s
- 50 µm layer11.3 sRange 11.2 to 11.4 s
- 100 µm layer12.3 sRange 12.2 to 12.4 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
HERO HD Pearl White
HERO HD Pearl White exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer12.7 sRange 12.6 to 12.8 s
- 50 µm layer12.9 sRange 12.8 to 13.0 s
- 100 µm layer13.9 sRange 13.8 to 14.0 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
HERO HD Sienna
HERO HD Sienna exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer12.1 sRange 12.0 to 12.2 s
- 50 µm layer12.3 sRange 12.2 to 12.4 s
- 100 µm layer13.3 sRange 13.2 to 13.4 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
HERO HD Merchant Grey
HERO HD Merchant Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer12.1 sRange 12.0 to 12.2 s
- 50 µm layer12.3 sRange 12.2 to 12.4 s
- 100 µm layer13.3 sRange 13.2 to 13.4 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
HERO HD Flesh
HERO HD Flesh exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer12.1 sRange 12.0 to 12.2 s
- 50 µm layer12.3 sRange 12.2 to 12.4 s
- 100 µm layer13.3 sRange 13.2 to 13.4 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 62.3 s, 4 transition layers
RPG settings on the Peopoly Phenom XXL
RPG Medium Grey
RPG Medium Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer13.7 sRange 13.6 to 13.8 s
- 50 µm layer13.9 sRange 13.8 to 14.0 s
- 100 µm layer14.9 sRange 14.8 to 15.0 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 71.2 s, 4 transition layers
Standard HD settings on the Peopoly Phenom XXL
Standard HD Dark Cool Grey
Standard HD Dark Cool Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer19.8 s
- 50 µm layer20.0 s
- 100 µm layer21.0 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 80 s, 4 transition layers
Standard HD Flat Grey
Standard HD Flat Grey exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer15.1 sRange 15.0 to 15.2 s
- 50 µm layer15.3 sRange 15.2 to 15.4 s
- 100 µm layer16.3 sRange 16.2 to 16.4 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 6 layers at 80 s, 4 transition layers
Platinum Cure Cast settings on the Peopoly Phenom XXL
These are starting values based on customer reports and similar clear resin data. Run a test print or exposure test first.
Platinum Cure Cast Clear
Platinum Cure Cast Clear exposure and burn in settings on the Peopoly Phenom XXL, by layer height
Normal layer exposure, starting value
- 30 µm layer16.7 sRange 16.6 to 16.8 s
- 50 µm layer16.9 sRange 16.8 to 17.0 s
- 100 µm layer17.9 sRange 17.8 to 18.0 s
Adjust 0.1 to 0.2 s as needed.
Burn in: 5 layers at 20 s, 5 transition layers
Printing directly on the build plate with no supports? Use about 3 s for 5 burn in layers, with 5 transition layers.
Platinum Cure Cast Clear lift, retract and wait settings on the Peopoly Phenom XXL
Burn in layers
- Lift distance, stage 1 (mm)
- 15
- Retract distance, stage 1 (mm)
- 15
- Lift speed, stage 1 (mm/min)
- 32
- Retract speed, stage 1 (mm/min)
- 100
- Wait before print (s)
- 0
- Wait after print (s)
- 0
- Wait after lift (s)
- 0
- Light intensity (%)
- 100
Normal layers
- Lift distance, stage 1 (mm)
- 14
- Retract distance, stage 1 (mm)
- 14
- Lift speed, stage 1 (mm/min)
- 35
- Retract speed, stage 1 (mm/min)
- 100
- Wait before print (s)
- 1
- Wait after print (s)
- 0
- Wait after lift (s)
- 0
- Light intensity (%)
- 100
Platinum Cure Cast print and bake tips
Before you print
- Settings assume supported prints. With supports, keep the burn in exposure at or under 15 to 20 s.
- If you print directly on the build plate, use a short burn in of about 3 s for 5 layers with 5 transition layers.
Orientation
- Print parts at an angle. Large flat areas facing the plate can cup and leave defects.
- Clear resin can close small holes, most of all holes that run along the Z axis. Orient parts so critical holes do not run straight up.
- Very small columns are hard to hold. If they fail, slow the lift speed, add a short rest and raise the exposure a little.
- Take care with thin walls, which can distort.
Post processing (required)
- Wash thoroughly in IPA.
- Let the part dry completely, overnight or with compressed air and about 3 hours of drying. Parts that are still wet can show surface problems.
- UV cure for 10 to 20 minutes.
- Bake at 275°F (135°C) for 60 to 80 minutes in a dedicated oven or air fryer, never a kitchen oven used for food.
The bake is what lets platinum silicone cure against the printed part. Without it the silicone will stay uncured where it touches the print.
Limits
- Made for open molds used with platinum cure silicone.
- Not recommended for closed or injected molds. In testing, injected silicone stayed uncured even after repeated cure cycles.
Lift, retract and wait settings for the Peopoly Phenom XXL
The maker profile uses a single stage lift, so only stage 1 values are listed. Field names follow Lychee Slicer. Use the same values in the matching fields of your slicer.
Lift, retract and wait settings on the Peopoly Phenom XXL for HERO HD, RPG and Standard HD (Lychee field names)
Burn in layers
- Lift distance, stage 1 (mm)
- 15
- Retract distance, stage 1 (mm)
- 15
- Lift speed, stage 1 (mm/min)
- 32
- Retract speed, stage 1 (mm/min)
- 100
- Wait before print (s)
- 0
- Wait after print (s)
- 0
- Wait after lift (s)
- 0
- Light intensity (%)
- 100
Normal layers
- Lift distance, stage 1 (mm)
- 14
- Retract distance, stage 1 (mm)
- 14
- Lift speed, stage 1 (mm/min)
- 35
- Retract speed, stage 1 (mm/min)
- 100
- Wait before print (s)
- 1
- Wait after print (s)
- 0
- Wait after lift (s)
- 0
- Light intensity (%)
- 100
Peopoly Phenom XXL resin settings FAQ
What exposure should I use for 3DRS HERO HD on the Peopoly Phenom XXL?
At 50 microns, start HERO HD Medium Grey at 10.6 s, Light Grey at 11.3 s and Pearl White at 12.9 s. Adjust 0.1 to 0.2 s as needed after a calibration print.
How many burn in layers should I use on the Peopoly Phenom XXL?
For HERO HD Medium Grey at 50 microns, use 6 burn in layers at 62.3 s, followed by 4 transition layers.
What lift and retract settings work on the Peopoly Phenom XXL?
For normal layers, lift 14 mm at 35 mm/min and retract at 100 mm/min. The lift and retract settings above list burn in values too.
What about RPG and Standard HD on the Peopoly Phenom XXL?
At 50 microns, start RPG Medium Grey at 13.9 s, Standard HD Dark Cool Grey at 20.0 s and Standard HD Flat Grey at 15.3 s.
What settings should I use for Platinum Cure Cast on the Peopoly Phenom XXL?
At 50 microns, start Platinum Cure Cast Clear at 16.9 s with 5 burn in layers at 20 s. These are starting values based on customer reports and similar clear resin data, so run an exposure test first. After printing, wash in IPA, dry fully, UV cure for 10 to 20 minutes and bake at 275°F (135°C) for 60 to 80 minutes before casting platinum silicone.
Need help dialing in your Peopoly Phenom XXL?
Email info@3dresinsolutions.com with your printer, resin and layer height. See settings for other printers.
